Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterPanel Replacement in Henderson, NV
A damaged garage door panel in Henderson usually costs between $250 and $800 to replace, depending on the panel size, material, and whether the door is insulated. Most single-panel replacements take under two hours once the panel is on hand, and we can match the existing door’s color and texture so the repair doesn’t stand out. If you’re looking at a dent from a basketball, a crack from a trailer hitch, or sun-warped sections on a west-facing door, call Fernbrook Garage Doors Henderson at (775) 458-7045 and we’ll give you a written price before any work starts.
Panel replacement is one of the most common repairs we handle across Henderson, from Green Valley Ranch to Anthem and Inspirada. It’s usually the right call when one or two sections are damaged but the rest of the door operates fine. Rather than replacing an entire door over a single dented panel, we swap the damaged section, verify the door’s balance and track alignment, and leave the rest of the system untouched. For a broader look at how panel work fits into the full picture of door health, visit our Garage Door Repair page or our Garage Door Repair in Henderson resource.
When You Need Panel Replacement
Not every dent calls for a new panel. Here are the situations we see most often in Henderson garages, and the ones that genuinely warrant replacement:
- Impact damage from a vehicle. A trailer hitch or bumper tap can crush a lower panel’s steel or aluminum frame. If the panel is bowed more than a half-inch, it’s usually cheaper to replace it than to try bending it back. In areas like Anthem with tighter driveways, we see a lot of lower-panel dents from slow-speed misjudgments.
- Cracked or split panels on west- and south-facing doors. Henderson sun is hard on garage doors. Years of direct afternoon heat can make vinyl and older wood-composite panels brittle. We regularly replace sun-damaged top sections in Green Valley and MacDonald Ranch where doors catch the full summer exposure.
- Rusted-through steel sections. If a panel has rust holes rather than surface rust, the structural integrity is gone. This is especially common on older non-insulated doors and on homes near the McCullough Hills where irrigation overspray reaches the door bottom.
- Bent rails or stiles from a child’s bike or sports gear. A solid hit from a bike handlebar or a lacrosse stick can dent the stile, the vertical support inside the panel. Once that support is bent, the panel loses rigidity and will flex every time the door cycles.
- Mismatched panel after a previous repair attempt. If a past repair left a panel that’s a slightly different shade or texture, replacing it with a properly matched section restores the door’s appearance. We keep manufacturer color charts for Clopay and Amarr panels to get the match right.
- Insulated doors with compromised cores. Once an insulated panel’s outer skin is punctured, the insulation degrades and the garage loses thermal efficiency. In Henderson’s summer heat, a punctured insulated panel means your garage absorbs more heat, which pushes into any adjoining rooms.
Our Panel Replacement Process
Replacing a panel is precise work. The existing panels, the track, and the spring tension all need to work together after the swap, and the new panel has to align within a fraction of an inch. Here’s the sequence we follow on every panel replacement in Henderson:
- We measure and identify the door. Before we order or source a panel, we measure the section height, check the manufacturer label, and note whether the door is insulated or non-insulated. This tells us which of the eight brands we’re trained on, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor, the panel matches.
- We give you a written price. You get the full cost on paper before we order anything or pick up a tool. That price includes the panel, any shipping, labor, and balancing. There’s no open-ended estimate and no surprise line item at the end.
- We protect your garage floor and any belongings near the door. Our technicians drop cloths on the concrete and move carefully around bikes, strollers, and storage. We ask before we move or touch anything, including a dog crate or a cooler pushed near the track.
- We swap the damaged panel. The door is brought down, the damaged section is detached from the hinges, and the new panel is set in place. We check the alignment against the panels above and below before re-securing the hardware.
- We re-tension and rebalance the door. A new panel changes the door’s weight, even slightly. We adjust the spring tension so the door opens and closes smoothly and doesn’t strain the opener. On doors with an automatic opener, we run a full cycle to verify the opener is lifting evenly.
- We clean up and show you the result. Sweep up any debris, remove the drop cloths, and wipe down the work area. Before we leave, we take a photo of the clean-up and review the work with you. Every panel replacement carries the 365-Day Done Right Promise, which means if something isn’t right, we make it right. No negotiation, no fine print.
Panel Replacement Pricing in Henderson
Panel replacement pricing in Henderson typically falls between $250 and $800 for a single panel, and between $600 and $1,600 when two or three panels are replaced together. Insulated panels run higher than non-insulated, and custom colors or wood-look finishes add to the material cost. Here’s how the pricing generally breaks down:
| Panel Type | Typical Single-Panel Cost (Parts + Labor) |
|---|---|
| Non-insulated steel panel | $250 – $400 |
| Insulated steel panel | $350 – $550 |
| Wood-composite or wood-look panel | $450 – $800 |
| Custom-color or painted panel | $400 – $750 |
| Two or three panels (common for sun damage) | $600 – $1,600 |
What moves the price most in Henderson is material availability. If your door is a current production model from Clopay or Amarr, the panel can often be sourced within a few days. If it’s an older or discontinued model, we may need to match the color and profile from inventory or fabricate a close approximation. We’ll tell you the sourcing timeline as part of the written price, before you commit to anything.
Some companies will suggest replacing the whole door when two or more panels are damaged. That’s sometimes the right call, especially if the door is 15 or more years old and the rollers and springs are nearing the end of their life. But we’ll lay out the numbers for repair versus replacement so you can decide with real figures in front of you. No one at Fernbrook is pushed to sell a full door when a panel swap solves the problem.
Every estimate is free, and the price we quote is the price on the invoice. Call (775) 458-7045 and we’ll schedule a time to look at the damage and hand you a written number.
FAQs – Panel Replacement
How much does it cost to replace one garage door panel in Henderson?
A single garage door panel in Henderson typically costs $250 to $800 installed, with non-insulated steel panels at the lower end and insulated or wood-look panels at the higher end. The total depends on material type, color match, and whether the door is a current production model. Call (775) 458-7045 for a free written estimate specific to your door.
Can you match the color and texture of my existing garage door?
In most cases, yes. We match against manufacturer color charts for Clopay, Amarr, and Raynor panels, and we source the panel from the same production line whenever the door is still in production. For older doors, we’ll match as closely as the available inventory allows and show you a sample before ordering. Minor sun fading may make a perfect match impossible, but we’ll be honest about what’s achievable before you spend anything.
Is it cheaper to repair a dented panel or replace it?
If the dent is shallow and the panel’s structure is intact, a repair can sometimes be done for $100 to $200 and we’ll tell you if that’s realistic. But once the stile is bent, the steel is rusted through, or the panel is cracked, replacement is the better value because a hammered-out repair often leaves visible creasing and a weaker panel. We’ll show you both options and the exact numbers for each.
Can you replace a panel the same day?
If the panel is in local inventory and the door is a common size, same-day replacement is often possible. We carry a range of stock panels for 16×7 and 8×7 doors, which covers many Henderson homes. For custom colors or less common panel profiles, plan on a few days for sourcing. Call (775) 458-7045 and we’ll check availability while you’re on the phone.
Do I need to replace the whole door if I have two damaged panels?
Not necessarily. Two damaged panels can often be replaced individually for $600 to $1,600 total, which is usually less than a full door replacement. The exception is if the door is older, the sensors need calibration, the springs are tired, or the track has sustained damage. We’ll give you both the panel-replacement price and the full-door price so you can make the call with complete information.
Why Henderson Families Call Fernbrook for Panel Work
A working door is the minimum. What most families in Henderson want is a repair that doesn’t introduce a new set of problems: muddy footprints through the kitchen, a technician who moves the stroller without asking, or a door that works but looks patched together. We built our process around exactly those concerns.
Every Fernbrook technician is background-checked and uniformed. Shoe covers go on before we step from the garage into the house, and drop cloths go down under the work area before the first hinge comes loose. If the work runs near nap time or during school hours, we keep tools quiet and the door cycling to a minimum. Pet-safe products are used wherever there’s a product choice, and we ask before moving a dog crate, a bike, or anything else near the track. The C.A.R.E. values aren’t a slogan; they’re a checklist: Clean up like it’s our own home; Ask before we move or touch anything; Respect the family’s time and quiet hours; Explain the price before the work. Our technicians follow those on every visit.
The written price is part of the Cedarwell Care Promise, which also includes the shoe covers, drop cloths, quiet tools, pet-safe products where there’s a choice, the clean-up photo, and the 365-Day Done Right Promise. It’s a specific, enumerable list, and if any part of it is missing, you should say something. We’re part of the Cedarwell family of independently owned and operated garage door businesses, founded in 2002, and every location is held to the same standards.
If you have a dented, cracked, or sun-damaged panel on your garage door, call Fernbrook Garage Doors Henderson at (775) 458-7045. A live person answers, day or night, and we’ll schedule a time that works around your family’s schedule. We’ll look at the door, hand you a written price, and let you decide. No pressure, no surprise invoices, just a door that looks right and works right.
Written by Jesse Calder, Owner at Fernbrook Garage Doors Henderson, serving Henderson.